MICRO-PAM

Version:

Product

Compact Fluorometer for Long-term Monitoring of Photosynthesis

Amber Version - MICRO-PAM

AMBER Version
Measuring Heads MICRO‑HEAD/3B and MICRO‑HEAD/3A

MICRO-PAM systems can be configured with measuring heads MICRO-HEAD/3B and MICRO-HEAD/3A. The measuring head MICRO-HEAD/3B probes photosynthesis with blue light which has a peak intensity at 460 nm and full width at half maximum of 27 nm (Fig. 1). MICRO-PAM and MONI-PAM systems employing blue light have successively proven itself in terrestrial and aquatic research.

The measuring head MICRO-HEAD/3A possesses an amber LED with emission peaking at 598 nm and a full width at half maximum of 22 nm (Fig. 1). Amber light is better absorbed by cyanobacteria than blue light. Correspondingly, the quality of the PAM signal excited by amber light is superior to that excited by blue light. For this reason, MICRO-PAM systems configured with measuring heads MICRO-HEAD/3A are particularly suited to probe cyanobacterial mats and lichens, or crusts containing cyanobacteria.

BLUE and AMBER Versions are further distinguished by the spectral window for fluorescence detection. The BLUE version detects fluorescence at wavelengths > 600 nm, whereas the AMBER version detects fluorescence at wavelengths > 700 nm (Fig. 2).

Figure 1: Typical LED emission spectra normalized to their maxima. The blue curve corresponds to the spectrum of the blue LED of the measuring head MICRO-HEAD/3B, the amber curve represents the emission of the amber LED of the measuring head MICRO-HEAD/3A. Peak wavelengths and full width at half maximum (bracketed) in nm are displayed.

Cold-acclimation of Leaves

A MICRO-PAM system was used to monitor acclimation of photosystem II to decreasing temperature in fall. Outdoor experiments were performed with leaves from holly (Ilex aquifolium) from October 9 to November 6, 2019. Position: latitude: 49.656564 | longitude: 11.09793.

During the monitoring period, the maximum FM’ showed a tendency to decrease and exhibited lowest values between days 20 and 24 (Fig. 1). On average, the PAR was higher at the initial part of the experiment compared to the final part, but a decrease comparable to the FM’ was not observed (Fig. 2).

Temperature showed a tendency to decrease. As observed for FM’, minimum values were recorded between das 20 and 24 (Fig. 3).

Analyzing the relationship between maximum FM’ and minimum temperatures by linear regression yielded a coefficient of determination of 0.6 (Fig. 4), suggesting that the two parameters are related to each other. Sustained non-photochemical quenching might be a factor involved in this fluorescence/temperature relationship.

Figure 1: Time course of FM’. Periods of darkness are in marked grey.

Lichen Photosynthesis (MICRO-PAM Prototype)

Prototypes of the measuring heads MICRO-HEAD/3B have been successfully employed to monitor photosynthesis of lichens growing under extreme climate conditions. Experimental sites include Tierra del Fuego and the Antarctica.

The poster below describes the experimental setup and shows long-term data of PAR, temperature, photosystem II yield and calculated electron transport rate.

Download Poster (PDF)

MICRO-PAM prototype installed near CHARS (Canadian High Arctic Research Station) Cambridge Bay, Nunavut; note the protection by wire mesh over the MICRO-PAMs and steel conduit over the cable, this is necessary protection against inquisitive local animals (lemmings, foxes and bears).

Scientific Publications using Walz Devices

Source: Google Scholar.
Keywords: (Walz OR Waltz) Effeltrich.
Date: June 22, 2026.

Ʃ = 19642

Per Year

Source: Google Scholar.
Keywords: (Walz OR Waltz) Effeltrich.
Date: June 22, 2026.

Ʃ = 19642

Year

Selected Publications

Harnessing LED technology for consistent and nutritious production of large-fruited tomatoes

Qiu N, Shen H, Ishizuka D, Yatsuda K, Kawabata S, Qu Y, Yamori W

HortScience 60: 1851-1859

Go to publication

Modulation of phenology and agronomical performance of Syrah grafted on rootstocks under combined salinity and water stress conditions: a three-year field study

Reta K, Lupo Y, Persi NS, Lazarovitch N, Fait A

Plant Stress 18: 101050

Go to publication

The ECOSENSE forest-enriching tower-based flux measurements of carbon and water exchange with novel distribute sensor networks

Sulzer M, Brzozon J, Christen A, Dedden L, Dormann CF, Dumberger S, Frey Y, Gassilloud M, Göritz A, Grote R, Haberstroh, Kattenborn T, Kremer L, Kreuzwieser J, Kühnhammer K, Lang F, Lee H, Müller J, Schack-Kirchner H, Seifert T, Stock C, Strack J, Tesch J, Wagner D, Wallrabe U, Weiler M, Werner C

ARPHA Conference Abstracts 8: e149267

Go to publication

Evaluation of comprehensive alkali resistance in tomato germplasm seedlings

Wang X, Song J, Fan W, He Z, Zhang X

Euphytica 221: 137

Go to publication

A novel multilayer cultivation strategy improves light utilization and fruit quality in plant factories for tomato production

Furuta H, Qu Y, Ishizuka D, Kawabata S, Sano T, Yamori W

bioRxiv-4

Go to publication

Field integration of shoot gas-exchange and leaf chlorophyll fluorescence measurements to study the long-term regulation of photosynthesis in situ

Oivukkamäki J, Aalto J, Pfündel EE, Tian M, Zhang C, Grebe S, Salmon Y, Hölttä T, Porcar-Castell A

Tree Physiology 45: tpae162

Go to publication

Novel methods facilitating the mechanistic interpretation of multiscale optical remote sensing measurements.

Oivukkamäki J

Dissertationes Forestales 349

Go to publication

Sinusoidal LED light recipes can improve rocket edible biomass and reduce electricity costs in indoor growth environments.

Stamford JD, Hofmann TA, Lawson T

Frontiers in Plant Science 15: 1447368

Go to publication

Effects of exogenous melatonin on Chrysanthemum physiological characteristics and photosynthesis under drought stress.

Luo Y, Hu T, Huo Y, Wang L, Zhang L, Yan R

Horticulturae 9: 106

Go to publication

Performance of singular spectrum analysis in separating seasonal and fast physiological dynamics of solar-induced chlorophyll fluorescence and PRI optical signals.

Biriukova K, Pacheco-Labrador J, Migliavacca M, Mahecha MD, Gonzalez-Cascon R, Martín MP, Rossini M

Journal of Geophysical Research: Biogeosciences 126: e2020JG006158

Go to publication

Characterization of river biofilm responses to the exposure with heavy metals using a novel micro fluorometer biosensor.

Carafa R, Lorenzo NE, Llopart JS, Kumar V, Schuhmacher M

Aquatic Toxicology 231: 105732

Go to publication

Metabolic activity duration can be effectively predicted from macroclimatic data for biological soil crust habitats across Europe.

Raggio J, Green TGA, Sancho LG, Pintado A, Colesie C, Weber B, Büdel B

Geoderma 306, 10-17

Go to publication

In situ monitoring of microclimate and metabolic activity in lichens from Antarctic extremes: a comparison between South Shetland Islands and the McMurdo Dry Valleys.

Raggio J, Green TGA, Sancho LG

Polar Biology 39: 113-122

Go to publication

MICRO-PAM (Amber Version - MICRO-PAM)

Housing
Aluminum case with RS-232, USB-B, Ethernet, power supply sockets, and four M12 5-pole sockets for RS-485 communication
Interfacing
The interface box connects a computer with up to four MICRO-HEAD/3B (or one MONI-DA). RS-485 serial data communication is used between interface box and MICRO-HEAD/3B or MONI-DA. RS232, USB or Ethernet communication is used between interface box and computer
Recommended maximum cable lengths
To computer via USB and RS-232: 2 m. To computer via Ethernet, 100 m. To MICRO-HEAD/3B via RS-485: 10 m. To MONI-DA via RS-485, 100 m
Dimensions
12 x 9.3 x 3 cm (L x W x H)
Weight
400 g
Operating temperature
0 to +40 °C
Power supply
Input: 100 to 240 V AC, 50 to 60 Hz. Output: 19 V DC, 3.7 A. Dimensions: 13.2 x 5.8 x 3 cm (L x W x H). Weight: 310 g
General design
Modulated fluorescence excitation
Amber power LED (typical peak wavelength 598 nm, full width at half maximum 27 nm). Photosynthetically active radiation (PAR) of measuring light at level of the sample clip range from 0.15 to 1.5 μmol m-2 s-1 at low modulation frequencies (5 to 25 Hz), and from 1.5 to 22.5 μmol m-2 s-1 at high modulation frequencies (100 Hz)
Actinic light
Same power LED as for modulated light. At sample level of leaf clip, 3000 μmol m-2 s-1 maximum PAR of actinic light, 8000 μmol m-2 s-1 maximum PAR of saturating flashes
Further specifications
Same as Measuring Head MICRO-HEAD/3B
Housing
Robust water-proof cylinder consisting of a polyvinyl chloride (PVC) tube and poly-oxymethylene (POM) endplates. One endplate with 2 male M12 5-pole sockets connected in parallel (MONI-IB4/LAN communication, charging voltage), one male M12 5-pole socket for auxiliaries, and 7 female M12 5-pole sockets (MICRO-PAM measuring head communication)
Dimensions
Cylinder with diameter of 16 cm and length of 24 cm
Data management
Dual data storage on internal 8 MByte circular flash buffer and an industrial grade 512 MByte removable microSD flash card. Wireless data transfer via cellular phone or satellite modem. Online data transfer using RS-485 serial data communication.
Power consumption

5 mW in standby mode. Operating mode, depends on the number of MONI-PAM measuring heads connected (see MONI-HEAD/485 power consumption)

Battery
12 V / 7.5 Ah (96 Wh) LiFePO4 battery.
Operating temperature
-30 to +60 °C
Weight
5.4 kg
Program

WinControl-3 System Control and Data Acquisition Program (Microsoft Windows 10/11) for operation of measuring system via PC, data acquisition and analysis. Not compatible with Windows 10 on ARM

Measured parameters
Ft, F0, FM, F, F0' (also calculated), FM'. Calculated: F0' (also measured), FV/FM and Y(II) (maximum and effective photochemical yield of PS II, respectively), qL, qP, qN, NPQ, Y(NPQ), Y(NO) and ETR (electron transport rate). Fitting Routines: Two routines for determination of the cardinal points α, Ik and ETRmax of light curves
Further date acquired
PAR, leaf temperature, humidity
Additional feature
Automatic determination of signal offset for all light intensities and all gain levels
Communication Protocol
USB
Computer Requirements
Processor, 1 GHz. RAM, 512 MB. Screen resolution, 1024 x 600 pixels. Interface, USB 2.0/3.0
Housing
Aluminum case with USB-B socket, power supply socket, and M12 5-pole socket for RS-485 communication
Links
The interface box connects a computer with a MONI-DA using RS-485 serial data communication. The same line is used to charge the MONI-DA battery. USB communication is used between interface box and computer
Recommended maximum cable lengths
To computer via USB: 2 m. To MONI-DA via RS-485,
100 m
Dimensions
9.7 x 6.3 x 3.5 cm (L x W x H)
Housing
Aluminum case with USB-B socket, power supply socket, and M12 5-pole socket for RS-485 communication
Weight
270 g
Recommended maximum cable lengths
To computer via USB: 2 m. To MONI-DA via RS-485,
100 m
Operating temperature
0 to +40 °C
Design

Two monocrystalline silicon panels. Waterproof and dustproof in accordance with IP 67. Each equipped with 0.9 m cables for the plus and minus poles. Including 2 x 0.4 m adapter for connecting the 2 panels in parallel, a 5 m extension cord, and a 0.4 m adapter for connecting to the AUX or INPUT port of the Data Acquisition System MONI-DA

Electrical characteristics

Vmax, 45.0 V, Imax, 1.14 A, Power 20 W

Dimensions

41.5 x 28.5 x 0.3 cm (L x W x H)

Weight

0.6 kg

Specification depend on available electronic components at the time of order

Program

WinControl-3 System Control and Data Acquisition Program (Microsoft Windows 10 and 11) for operation of measuring system via PC, data acquisition and analysis. Not compatible with Windows 10 on ARM

Saturation Pulse Analysis

Measured: Ft, F0, FM, F, F0’ (also calculated), FM’. Depending on the leaf clip connected, the software can record PAR, temperature and also humidity. [In the case of the MINI-PAM-II clip humidity can be measured, which the clip of the JUNIOR-PAM cannot.]
Calculated: F0’ (also measured), FV/FM and Y(II) (maximum and effective photochemical yield of PS II, respectively), qL, qP, qN, NPQ, Y(NPQ), Y(NO) and ETR (electron transport rate)

Fitting Routines

Two routines for determination of the cardinal points α, Ik and ETRmax of light curves

Programmed Features

Automatic determination of signal offset for all light intensities and gain levels. Automatic calibration of internal PAR sensor against an external PAR sensor connected to the instrument

Computer Requirements

Processor: 0.8 GHz, RAM: 512 MB, screen resolution: 1024 x 600 pixels, interface: USB 2.0/3.0

Communication Protocol

USB

Design

Aluminum box with custom foam packing MICRO-PAM

Dimensions

60 cm x 40 cm x 34 cm (L x W x H);
60 liter

Weight

4.9 kg

Accessories

Design
Two double-ball arm segments, two ball end pieces with photo thread (1/4” external), to mount a measuring head and a base plate with photo thread (1/4" internal), respectively.
Dimensions
39 cm (L max.)
Weight
410 g
Housing
Aluminum case with one M12 5-pole connector and four M8 5-pole connectors
Links
The interface box connects up to four MICRO-PAM measuring heads to one single MONI-BUS port of a MONI-DA data acquisition system
Recommended maximum cable lengths
10 m between MICRO-PAM measuring head and MICRO-HUB, and between MICRO-HUB and MONI-DA
Dimensions
10 x 6 x 3.5 cm (L x W x H)
Weight
228 g
Operating temperature
-30 to +40 °C
Recommended maximum cable lengths
10 m between MICRO-HEAD/3B and MICRO-HUB, and between MICRO-HUB and MONI-DA
Design
Weatherproof cylinder made of POM (Polyoxymethylene) containing a standard WiFi modul. One endplate made of POM, the other endplate made of Plexiglas with 5-pole M12 plug connector. Includes a 10 m cable to connect the modem to the AUX port of the MONI-DA. Data transfer requires connection to a compatible WiFi network or hotspot (2.4 GHz, IEEE 802.11 b/g/n, WPA2-PSK)
Dimensions
19.5 cm (L) 3.27 cm (Ø)
Weight
140 g (modem), 320 g (cable)

See the MICRO-PAM in action

On June 10, 2026, after 7 years of recording photosynthesis of trees, a new experiment was started. Now, our monitoring station at the Walz headquarters streams live chlorophyll fluorescence data from ivy (Hedera helix). Five MICRO-PAM fluorometers continuously record photosynthetic yield, light intensity, temperature, and humidity - 24 hours a day, 7 days a week.

Three types of live graphs are available: Y(II) + PAR, Y(II) + ETR, and Temperature + PAR + Humidity. Data can be downloaded and displayed using the WinControl-3 software.

loading...
Y(II), PAR
Y(II), ETR
Temp., PAR, Hum.
Download
Ch. F Fm' Y(II) PAR 1) ETR 1) Temp. °C Air Hum. %
1) µmol m-2 s-1
Live view of the experimental site

ONLINE Configuration of MICRO-PAM

In the ONLINE configuration, the MICRO-PAM system is operated by the Software WinControl 3 running on a Windows computer. Up to 4 MICRO HEAD/3B can be connected to a computer USB port using the PC Interface Box MONI-IB4/LAN. The standard cable length between PC Interface Box MONI-IB4/LAN and MICRO HEAD/3B is 10 m.

The PC Interface Box MONI-IB4/LAN permits integration of the Online configuration into a local area network (LAN). The Ethernet port can be located at a distance of up to 100 m away from the MONI-IB4/LAN. For special applications, the interface box also offers RS 232 communication.

ONLINE configuration. The scheme indicates the three communication options of the ONLINE Configuration: USB, RS232, and Ethernet.

STAND-ALONE Configuration of MICRO-PAM

The STAND-ALONE configuration comprises the data acquisition system MONI-DA which permits battery-powered operation of the MICRO-PAM system. The STAND-ALONE configuration includes solar panels allowing data acquisition for very long periods of time independent of line power. An optional modem sends live data to a dedicated server for download by the user.

The Four-Way Distributor MICRO-HUB connects 4 measuring heads MICRO-HEAD/3B to a single port of the MONI-DA. The maximum number of measuring heads MICRO-HEAD/3B per MONI-DA is 16. As the MONI-DA has 7 input ports, the number of 16 is achieved using 3 MICRO-HUB interfaces each connecting 4 measuring heads to the MONI-DA, and linking directly another 4 measuring heads to the MONI-DA.

WinControl-3 Software for MICRO-PAM

General Features and Graphical User Interface

The WinControl-3 is a very versatile software dedicated to operate a certain class of Walz PAM fluorometers. The software executes classical experimental routines like fluorescence induction and light response curves, but also acquires and graphically display data.

WinControl-3 not only operates the MICRO-PAM but also the DIVING-PAM-II, JUNIOR-PAM, MINI-PAM-II, and MONITORING-PAM fluorometers, as well as PAM-CONTROL operated instruments (MICROSCOPY-PAM, MICROFIBER-PAM and WATER-PAM) and the Universal Light Meter ULM-500.

Data Evaluation

Saturating pulse analysis with automatic detection of fluorescence levels F0, FM, F, and FM’. Calculation of F0’ level fluorescence and of standard fluorescence parameters. Specifically, photochemical yield of photosystem II, FV/FM and Y(II), photochemical quenching, qP and qL, non-photochemical quenching, qN, NPQ, Y(NPQ), and Y(NO), and electron transport rate, ETR.

 

Advanced Features

All experimental protocols can be performed automatically using the batch file feature of WinControl-3. Convenient programming of experiments using the built-in macro recorder. The software is capable of DDE communication with peripheral machines.

 

Automated Routines

Repetitive triggering of fluorometer functions (e. g., dark-light induction and dark recovery curves) by adjustable clock. Automatic execution of light exposure protocols and fitting of two different model functions to data of light response experiments.

 

Data Export

Export of original fluorescence traces, saturating pulse analysis data and parameter estimates of light response curves as semicolon- or tab-separated data.